Good operating habits are very important. Operators have a certain understanding of aluminum door and window equipment in operating the equipment, including the control mode and various technical indicators of operating the equipment, and check the equipment parts during startup, including whether there are fragments, mechanical parts, processed parts and whether the operating parts are normal.

使用中的設備環境也很重要，一般設備環境以干燥清潔的環境為主，斷橋鋁門窗設備的維護、維護方式很重要，首先定期清洗，每次設備加工中，都會在設備的各個構成部件上留下各種瑣碎的東西，經過時間的積累，各個部件都會形成特殊的雜質組

The equipment environment in use is also very important. Generally, the equipment environment is mainly dry and clean. The maintenance and maintenance method of broken bridge aluminum door and window equipment is very important. First, it is cleaned regularly. In each equipment processing, various trivial things will be left on each component of the equipment. After the accumulation of time, each component will form a special impurity group

使用專用潤滑油潤滑設備的連接部位，同時根據平時的加工需要對門窗設備進行進料和調試，如調試切割設備的緊固程度和切割角度，適當調整導軌的精度，設備的電路也可以在使用過程中進行維修。

Use special lubricating oil to lubricate the connecting parts of the equipment. At the same time, feed and debug the door and window equipment according to the usual processing needs, such as debugging the fastening degree and cutting angle of the cutting equipment, properly adjusting the accuracy of the guide rail, and the circuit of the equipment can also be repaired during use.

維修設備需要遵循由外而內的原則，檢查設備外部是否有明顯的裂痕、缺損，,然后再對其內部進行檢測，拆前應排隊周邊的故障因素，確定為機內故障后才能拆卸，否則盲目拆卸，可能將門窗加工設備越修越壞，先機械后電，氣只有在確定機械零件無故障后，再進行電氣方面的檢查，檢查電路故障時，應利用檢測儀器尋找故障部位，確認無接觸不良故障后，再有針對性地查看線路與機械的運作關系，以免判斷失誤。

The maintenance equipment shall follow the principle of "from the outside to the inside", check whether there are obvious cracks and defects on the outside of the equipment, and then inspect its inside. Before disassembly, queue up the surrounding fault factors, and disassemble it only after it is determined that it is an internal fault. Otherwise, blind disassembly may damage the door and window processing equipment more and more. Machinery first and then electricity, and gas only after it is determined that there is no fault on the mechanical parts, Then conduct electrical inspection. When checking the circuit fault, use the detection instrument to find the fault part. After confirming that there is no poor contact fault, check the operation relationship between the line and the machinery, so as to avoid misjudgment.

設備先不要通電，判斷設備的按鈕、線路等是否出現問題，從而判定故障的所在，通電試驗，聽其聲、測參數、判斷故障，之后進行維修，如在電動機缺相時，若測量三相電壓值無法著判別時，就應該聽其聲，單獨測每相對地電壓，方可判斷哪一相缺損，先清潔后維修，對污染較重的斷橋鋁門窗設備，先對其按鈕、接線點、接觸點進行清潔，檢查外部控制鍵是否失靈，許多故障都是由臟污及導電塵塊引起的，一經清潔故障往往會排除。

Do not energize the equipment first, judge whether there is a problem with the buttons and lines of the equipment, so as to determine the fault. Conduct the power on test, listen to the sound, measure the parameters and judge the fault, and then carry out maintenance. If the three-phase voltage value cannot be judged when the motor is out of phase, you should listen to the sound and measure the voltage of each phase to ground separately, so as to judge which phase is out of phase, Clean before maintenance. For the heavily polluted broken bridge aluminum door and window equipment, clean its buttons, wiring points and contact points first, and check whether the external control keys fail. Many faults are caused by dirt and conductive dust. Once cleaned, the faults are often eliminated.

數控門窗設備專注為您提供新鮮的行業資訊,更多的問題及精彩內容請關注我們的網站：http://www.jinesu.com ，我們會有更多的精彩內容為您呈

CNC door and window equipment focuses on providing you with fresh industry information. For more questions and wonderful contents, please pay attention to our website: http://www.jinesu.com , we will have more wonderful content for you